DSP-10 Help Screens. This is a text file that is displayed on
the DSP-10 screen when the help command (F1) is executed.
This file can be edited to customize the display.  This is 
useful when keys are customized, but can be used anytime.

Listed below, in the text for each screen, is a line of
numbers that help you count the number of characters.
There are 63 numbers corresponding to the 63 character limit.
This line must remain, as is,  to identify the start of each
screen. Additional screens can be added by copying the "number
line," followed by up to 22 lines of text.  Lines longer than
63 characters, or screens of more than 22 lines will be
truncated.  A vertical line, "|", shows the center of the line,
and is useful for setting up two columns.

This file uses the 8-bit ASCII set, and allows accents.
The CR (13) and LF (10) are taken as end of line, either or
both. Empty lines are ignored and a blank line should include
at least one space.  Do not use tabs for spacing lines.

The last screen in this file should be 8 lines, or less, 
allowing for EME location data at the bottom.  If more than 8
lines, the top of the screen showing the EME locations will be
blank. This is not harmful, but also not aesthetically pleasing!

Further comments can be added, here. They must precede the first
"number line."

Rev 6 July 06 RSL

123456789012345678901234567890|23456789012345678901234567890123
             DSP-10 KEYBOARD COMMANDS - Screen 1
       FREQUENCY                                GAIN
1 Hz     Ctrl-Alt-Sh F9, F10  |   AF Gain      Arrows or F7, F8
10 Hz                F9, F10  |   Mute toggle         Page Down
100 Hz            Sh F9, F10  |   RF Gain Down 6 dB       Sh F7
1 kHz            Alt F9, F10  |   RF Gain Up 6 dB         Sh F8
10 kHz          Ctrl F9, F10  |   Mike Gain Down 1 dB Alt-Sh F7
100 kHz     Ctrl-Alt F9, F10  |   Mike Gain Up 1 dB   Alt-Sh F8
1 MHz        Ctrl-Sh F9, F10  |   Require Scroll Lock On:
Cursor Tune (delf)    <-, ->  |   AGC Release Faster     Scrl G
Fast Tune(delf_sh) Sh <-, ->  |   AGC Release Slower     Scrl H
Text Entry             Alt-9  |   CW Sidetone Down 1 dB  Scrl S
EME Doppler Corr  Alt L or l  |   CW Sidetone Up 1 dB    Scrl D
     TRANSMIT/RECEIVE         |   CW Offset Down         Scrl C
T/R Toggle              Home  |   CW Offset Up           Scrl V
         RIT                  |         RCVR AF FILTERS
RIT 10Hz Down     Alt R or r  |   Filters On/Off             F3
RIT 10 Hz Up      Alt T or t  |   Filter Select              F4
RIT On/Off Togl   Alt O or o  |   Filter Design         Scrl F4
RIT Zero          Alt Z or z  |   Binaural Toggle         Alt-E
RIT 1Hz Up   Ctrl-Alt R or r  |   DeNoise On/Off          Sh F3
RIT 1Hz Dwn  Ctrl-Alt T or t  |   De-Noise Gain    Ctrl F3 & F4
123456789012345678901234567890|23456789012345678901234567890123
             DSP-10 KEYBOARD COMMANDS - Screen 2
          FM                            SPECTRUM DISPLAY
Squelch Down     Alt S or s   |   Spectral Ave       Alt F3, F4
Squelch Up       Alt D or d   |   Spectrum Width       Alt J, j
       CW or LTI              |   Norm Spectrum Fast Alt Q or q
Msg n (cfg)   Ctrl-Alt-Sh n   |   Norm Spectr 10 min Alt P or p
Alphanumeric  Any key in CW   |   Spectr Norm Off (toggle P, Q)
Delete Last Ch    Backspace   |   Color Display AGC  Alt C or c
Delete Buffer  '%',  Sh DEL   |   IF bandwidth W/N        Alt $
CW Speed         Alt F7, F8   |   Spectr Disp dB/div      Alt 1
CW: T to R              '!'   |   Spectr Disp U/D 1dB  Alt 2, 3
AR, SK             '[', ']'   |   Spec Data to File    Alt F, f
AS                      '\'   |   Audio Processor    Ctrl-Alt O
1 Sec On/Off    '{' and '}'   |   Mode=cw, usb, lsb... Alt M, m
CW Repeat Delimiter     '#'   |   Single Cursor     Ctrl A or a
CW Repeat Break         '@'   |   Double Cursor     Ctrl D or d
Long Key Down (frm CFG) '~'   |        SPECTRAL WATERFALL
           LTI                |   Clear Lower Box   Ctrl-Y or y
Box for setup    Alt B or b   |   Brightness Down            F5
Reset averaging Ctrl W or w   |   Brightness Up              F6
Flatten display Ctrl E or e   |   Contrast Down           Sh F5
                              |   Contrast Up             Sh F6
123456789012345678901234567890|23456789012345678901234567890123
             DSP-10 KEYBOARD COMMANDS - Screen 3
          OTHER                            PUA-43
Change Bottom Line   Scrl F3  |  Box for setup       Alt B or b
Exit to DOS      Scrl-Alt F4  |  Box for data disp   Alt A or a
DOS Visit           Alt-Sh 5  |  Clock Set      See Next Screen
Beacon parameters    Scrl F2  |  Reset averaging    Ctrl W or w
Beacon Activate   Alt H or h  |  Reset tuning   Ctrl-Alt W or w
Change EME Location '<', '>'  |  Reset characters      Scrl F10
Xmit Audio Equalizer Scrl F5  |
Xmit Power U/D 1dB Scrl O, P  |           LHL-7
Current setting to CFG Alt 0  |  Boxes and Clock as for PUA-43
        VFO SELECTION         |  Morse Ident xmit           '&'
2-meters    Ctrl-Alt 1,2...5  |  Tone Pattern xmit          '+'
50 MHz Trnsvrtr   Ctrl-Alt A  |
144:B   222:C  432:D   903:9  |           EME-2
1296:E  2304:F ... 145GHz:N   |  Boxes as for PUA-43
       MEMORY SELECTION       |  Reset averaging    Ctrl W or w
Write to Memory   Alt N or n  |  Activate                  Home
Read Memory      Ctrl N or n  |  
Freq,Mode to VFO Scrl N or n  |           BEACON
List to Screen    Scrl-Alt n  |  Beacon Parameters      Scrl F2
List to File      Scrl-Alt N  |  Beacon Activate     Alt-H or h
123456789012345678901234567890|23456789012345678901234567890123
             DSP-10 KEYBOARD COMMANDS - Screen 4
        TRANSMIT TONES        |     POWER CONTROLLED TONE
Setup FM & SSB tones Scrl F7  |  Box for Setup      Ctrl V or v
FM DTMF       0-9, A-D, *, #  |  On/Off              Alt V or v
                              |  Reset Frequency     Alt X or x
     SIGNAL SIMULATION        |           TIME CLOCK
Box for Setup        Scrl F6  |  Clock Parameter Box    Scrl F8
                              |  Manual Clock Set    Alt K or k
        DIAGNOSTICS           |  GPS Clock Sync     Scrl T or t
DSP Reset   Scrl-Ctrl-Alt-F4  |
                              |          DISPLAY STYLE
    DISTANCE and BEARING      |  Toggle Slide-Rule   Alt-Y or y
Display Table     Alt-U or u  |  Display mHz Toggle Scrl-Z or z
Edit Entry       Ctrl-U or u  |
