======== Part List - SDR Control Box - W7PUA Rev 31 Jan 2019 ============== ON BOARD PARTS Designator Qty Description C4,C5 2 0.001 uF NPO/COG 0805 Ceramic 478-3760-1-ND (rev 1-19, was 1276-1147-1-ND) C14,C10,C15, C11,C16,C8, C17,C9 8 0.1 uF, 50V, X7R, 0805 Ceramic 478-1395-1-ND (rev 1-19, was 1276-1003-1-ND) C12,C13,C7, C3,C2,C1, C20,C19,C18, C21 10 0.47 uF, 50V, 0805 Ceramic Y5V 478-10558-1-ND (rev 1-19, was 1276-6499-1-ND) C6, C35 1 100uF, 10V, 1206 or 1210 Ceramic 587-1965-1-ND (rev 1-19, was 445-11682-1-ND) C34 1 10uF, 25V, 0805 X5R 1276-2891-1-ND C26,C28,C25, C24,C22,C23, C29,C30,C31, C27 10 470 pF, 50V, NPO/COG 0805 Ceramic 478-1324-1-ND (rev 1-19, was 1276-1121-1-ND) D1,D5 2 FM4005 MOU 583-FM4005-T D3 1 Hdr for LED_Red_Green 732-5323-ND (cut down) see below *! D2,D4 2 BAS16-HT1G BAS16HT1GOSCT-ND F2,F1 2 Polyfuse_100mA 507-1794-1-ND F3 1 Polyfuse_500mA 507-1786-1-ND J1 1 Hdr for Audio Out Left 732-5323-ND (cut down) J2 1 Hdr for Audio Out Right 732-5323-ND (cut down) J3 1 Conn_01x05 732-5323-ND (cut down) J4 1-HOST Hdr for TeensyHostUSB 732-5323-ND (cut down) J6 1 CONN_01X14 732-5323-ND (cut down) L1 1 10 mH RLB-0812-103KL-ND L3,L2 2 Ferrite_Bead_Small 490-13267-1-ND L4,L9,L11, L10,L13,L12, L15,L7,L6, L5,L16,L17, L8,L18,L14 15 BLM21PG331SH1D 330 Ohm ferrite bead, 0805, 490-7823-1-ND (rev 1-19 corrected from 490-13267-1-ND) L21 1 220 uH, 9mm dia, radial lead RLB0914-221KL-ND P1 1 Conn_01X09 732-5323-ND (cut down) P2,P3 2 Conn_01x02 732-5323-ND (cut down) P5,P4 2 Conn_01x06 732-5323-ND (cut down) P7 1-SL To RJ-45 Connector 1x8 hdr 732-5323-ND (cut down) P6,P8,P9 3 Conn_01x05 732-5323-ND (cut down) P10 1 To Buttons 732-5323-ND (cut down) P11 1 To OptoEnc1 732-5323-ND (cut down) P12 1 To OptoEnc2 732-5323-ND (cut down) P13 1 To OptoEnc3 732-5323-ND (cut down) P14 1 25-pin male D-Sub, DigiKey 1174-125MEA-ND NorComp Inc. 174-E25-113R001 CONN D-SUB PLUG 25POS R/A SOLDER (rev 1-19 added info) P15 1 Conn_01x04 732-5323-ND (cut down) Q1 1-SL MMBT3904 MMBT3904FSCT-ND RV1 1-POT 5K pot, Bourns 3339P-1-502 or sim. 3339P-502-ND or similar R37 1 1-Ohm pkg 0805/1206 R14,R11,R13 3 1.0K pkg 0805/1206 R3 1 100 pkg 0805/1206 R15,R12,R4 3 10K pkg 0805/1206 R7,R5,R35, R36,R34 5 1K pkg 0805/1206 R32 1 220 pkg 0805/1206 R33 1 0.1-Ohm pkg 0805/1206 73L3R10JCT-ND (for 0805) R2,R1 2 330 pkg 0805/1206 R29,R24,R20, R18,R16,R21, R19,R17,R22, R25,R26,R23, R27,R28,R9, R31,R30 17 4.7K pkg 0805/1206 R8,R10 2 470 pkg 0805/1206 R6 1 82 pkg 0805/1206 SW1 1 SW_Push 732-5323-ND (cut down) see below *@ U1 1 LTC6912CGN-2 LTC6912CGN-2#PBF-ND U2 1 Socket - Teensy36 see below ** U3 1 Socket - Teensy36_Expand_2x7 ** U4 1 Socket - Teensy36_Expand_1x5 ** U5 1 74LVC595AD 1727-6688-1-ND U7,U6 2 MAX3232 MAX3232CSE+-ND U9,U10,U8, U11 4 74LV4T125 296-40545-1-ND U12 1 NCP1117DT33G NCP1117DT33GOS-ND 1 Main PC Board OSH Project SDR_Ctrl1r4 OFF BOARD PARTS 2 Rotary Encoder, Bournes PEC11L-4125F-S0020 PEC11L-4125F-S0020-ND 1 Rotary Encoder, High Res see text. 1-SL Gravitech RJ45-TERM MOU 992-RJ45-TERM 1 PJRC Teensy 3.6 Processor Board PJRC Part# TEENSY36 1 PJRC Teensy Audio Adaptor Part# TEENSY3_AUDIO 1 PJRC 320x240 Touch Screen Display Part# DISPLAY_ILI9341_TOUCH 1 Teensy 3.6 Extender Board OSH Project T36Extension_vp2 1 Set Stackable headers. These come as 5 strips of 36. ADAFRUIT 3366 These can be used for the Teensy and the Extender Board and from the top hold the Audio Adaptor board. 1 Enclosure Box, to suit Metal 4 RCA Connectors or similar 1-SER DB9 Panel Plug 2-SER DB9 Panel Socket 4 Sets of 4-4 or 3mm mounting hardware 1 8-pin DIN Socket CP-1280-ND 1-HOST SparkFun USB Socket on PCB MOU 474-808-12700 1 Red/Green LED on panel, MOU 696-SSL-LX5093IGW or DigiKey 67-2207-ND (rev 1-19 added DK) All fixed resistors are 5% 0805 or 1206 chip (pads will accept either). Chip cap and chip ferrite bead parts are on pads that accept either 0805 or 1206. Parts marked "SL" are needed only if hardware for "Signal-Link" clone is desired. Parts marked "SER" are needed only if RS-232 serial ports are desired. Parts marked "POT" are needed for an on-board adjustable voltage source. Parts marked "HOST" are needed for supporting a "Host" USB port from the Teensy. "Device" USB communications is through the USB micro-B connector on the Teensy. ** U2 is the standard Teensy 3.6 board and requires 2 24-pin sockets for 0.025-inch pins. U3 and U4 are not separate parts but rather sockets to accept pins from the Teesy 3.6 extension board. This is 2 7-pin sockets and 1 5-pin socket. *! The red/green LED is off board. D3 is misnamed and is a 2-pin header. *@ The switch is off board. SW1 is misnamed and is a 2-pin header. OSH = OSH Park https://oshpark.com/shared_projects and do search by project name OSH Park boards are ordered in multiples of three. PJRC = https://www.pjrc.com/store/ Teensy 3.6 is without pins: https://www.pjrc.com/store/teensy36.html Audio Adaptor: https://www.pjrc.com/store/teensy3_audio.html Touch screen: https://www.pjrc.com/store/display_ili9341_touch.html ADAFRUIT = https://www.adafruit.com for the headers, https://www.adafruit.com/product/3366 Initial 14 April 2018 Rev 26 Jan 2019 - Added audio adaptor, main PCB, stackable headers. Rev 31 Jan 2019 - Changed part # for availability. Thanks to KD7TS